Serial Port Opened
monitor start
Serial Port Closed
upg or dump task  is canceled!
monitor stop
Upgrade thread exit
monitor exit
Serial Port Opened
monitor start
---------------Time Stamp[14:12:22]----------------
---------------Time Stamp[14:17:22]----------------
download start
Please reboot the STB manually.
Change baudrate to 115200.
monitor stop
Serial Port Closed
upg or dump task  is canceled!
Serial Port Opened
monitor start
monitor stop
Sync Succeed.
Sending boot init...
Send boot init completed.
boot init run successfully.
SendClient.
Sending Client is complete.
Client is up.
Client Functionality is good.
uboot run successful
download successful!
monitor start
usb start;fatload usb 0 83000000 flash_ddr2.bin;sf burn 83000000 0 400000;
(Re)start USB...
auto_detect_usb_port --- usb default sel port 1
port_sts0:0x00000803 port_sts1:0x0c000000 
auto_detect_usb_port --- usb sel port 0
USB:   usb_debug 
need usb0 plug in.... 
usb0 device connect port status :0x1803 
port0 reset down port status :0x8001205 
ehci_hcd_init...
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
       scanning bus for ethernet devices... 0 Ethernet Device(s) found
reading flash_ddr2.bin

8388608 bytes read
do_spi_flash_uboot_save offset[0] len[800000]
spi0 is already setup!!!
SF: spi flash status register: 0x00, 0x00
SPI: Detected EN25QH64A with erase size 64 KiB, total 8 MiB
save uboot to flash
system will reboot
ROM
MCPU: version:btinit VER 0.0.5_sym:[hg_65_39fc899061c5] Build Time:[Mar 15 2018, 18:06:32]B$BBBBCBBBU
*****************************************
**  Board: mips CPU: sym - MIPS 24KEc
**  SOC name  : 0x8009
**  PACKET type : SIP_68S_DDR2
*****************************************
DRAM:  
DDR is 64MiBytes
20 MiB
10123**************load info***************
 ota_number:0x1,  curr_ota_id:0x87,  back_ota_id:0x8d,
load_block_id:0x88,  ota_tri:0
destroy flag:0x0,  destroy_block:0x0
**************load info end***************
bl_info.load_block_id = 0x88
fast load block id:0x88
*****************************************
**  Board: mips CPU: sym - MIPS 24KEc
**  SOC name  : 0x8009
**  PACKET type : SIP_68S_DDR2
*****************************************
DRAM:  20 MiB
10123g_usb_bus * g_usb_bus = 80AD5040 g_usb_bus * g_usb_bus = 80AF20E0 &ehci->regs->port_status[0] bf060084
ehci->regs->port_status[0] 803
ehci_port_status: PORT_CONNECT
###step1.2### 2 usb_hcd_poll_rh_status 


 ###step2###2 usb_hcd_poll_rh_status  msgq 0  hcd->bus 80af20e0


 ###step3### msg.event 2
priv->cfg.p_dem_bus =0x80a8e140
serial_open
[register_rtsp_stream][ERROR][ERROR] --do nothing !!!!!!!!!!
[register_rtsp_stream] please config ENABLE_DEMUX_RTSP = Y!!!!!! !!
&ehci->regs->port_status[0] bf060084
ehci->regs->port_status[0] 803
ehci_port_status: PORT_CONNECT
USB @2 start enumerate ports3c08bfc0 
hub_add_new_dev 80b52e60
port_reset 80af2000
&ehci->regs->port_status[0] bf060084
ehci->regs->port_status[0] 8000205
###step1.2### 0 usb_hcd_poll_rh_status 
**LCK UDQ**: 2cbc
[AI][_ai_mdl_init]Software Ver[1000000]
eve0
---------------Time Stamp[14:22:22]----------------
Upgrade thread exit
monitor exit
